Filters
Question type

Study Flashcards

To view immobilizer codes a ________ must be used.


A) generic scan tool
B) factory scan tool
C) factory test light
D) Any of these, depending on the vehicle

E) A) and B)
F) A) and C)

Correct Answer

verifed

verified

The immobilizer module communicates with the PCM using ________.


A) a serial data line
B) FM radio waves
C) a battery sender
D) the key fob

E) C) and D)
F) A) and B)

Correct Answer

verifed

verified

A typical Chrysler immobilizer system is called ________.


A) Passlock
B) SKIS
C) VATS
D) PATS

E) All of the above
F) C) and D)

Correct Answer

verifed

verified

Diagnosing an immobilizer requires the use of ________ and accurate service information.


A) a locksmith
B) jumper wires
C) a key code writing device
D) a scan tool

E) A) and D)
F) B) and C)

Correct Answer

verifed

verified

What can occur if the immobilizer system is not working as designed?


A) The engine cranks but does not start
B) The engine starts but then almost immediately stalls
C) No crank condition (the starter does not operate)
D) Any of the above

E) None of the above
F) B) and C)

Correct Answer

verifed

verified

How is data transmitted between the key and the steering column (lock cylinder) ?


A) Transferred from the key to the BCM using a small transmitter in the key
B) Transmitted from the key to the vehicle using the battery inside the key
C) By inductive coupling
D) By electrical contacts inside the lock cylinder

E) A) and C)
F) A) and B)

Correct Answer

verifed

verified

C

If an immobilizer-related fault occurs, what symbol is likely to be displayed on the dash?


A) "IM"
B) The "check engine" light
C) A padlock symbol
D) The "service engine soon" light

E) A) and B)
F) B) and C)

Correct Answer

verifed

verified

C

The vehicle security transceiver antenna may be located ________.


A) under the passenger seat
B) on the rear window defogger grid
C) in the console
D) at the key lock cylinder

E) A) and B)
F) C) and D)

Correct Answer

verifed

verified

A typical Ford immobilizer system is called ________.


A) Passlock
B) VATS
C) PATS
D) SKIS

E) A) and D)
F) B) and C)

Correct Answer

verifed

verified

If an immobilizer-related module is replaced, what needs to be performed?


A) The key(s) will need to be replaced to match the new module.
B) The module will need to be programmed with the security information to be able to function with the existing key.
C) All of the immobilizer-related modules need to be replaced at the same time so they will all work together.
D) Any of the above, depending on the make, model, and year of vehicle.

E) All of the above
F) B) and C)

Correct Answer

verifed

verified

Some Ford security system keys can be programmed using ________.


A) one original key
B) a lock programmer
C) two programmed keys
D) a door lock key

E) A) and B)
F) A) and D)

Correct Answer

verifed

verified

What is the purpose and function of an immobilizer system?


A) Only allows the use of the ignition key that is properly matched to the lock cylinder
B) Prevents the vehicle from starting or running if the correct key is not used
C) To prevent entry inside the vehicle
D) Requires that the driver enter a password to start the vehicle

E) A) and D)
F) B) and C)

Correct Answer

verifed

verified

A General Motors Passkey III system has the transponder located in the ________.


A) cylinder coil
B) head of the key
C) lock magnets
D) key fob

E) A) and B)
F) A) and C)

Correct Answer

verifed

verified

What will happen if a fault occurs in the immobilizer system when the engine is running?


A) The security light will come on and the engine will shut off
B) The engine will run at reduced power
C) The security light will come on but the engine will not be shut off
D) None of these

E) C) and D)
F) All of the above

Correct Answer

verifed

verified

An immobilizer fault may occur if the ________.


A) key is exposed to any kind of magnetic field
B) key gets wet
C) key is dropped onto a hard surface
D) Any of the above

E) A) and B)
F) A) and C)

Correct Answer

verifed

verified

What does the battery in the key fob power?


A) The remote keyless entry (RKE) transmitter
B) Both the remote keyless entry and the immobilizer circuit
C) The shock sensor
D) The immobilizer circuit

E) C) and D)
F) B) and C)

Correct Answer

verifed

verified

A

To prevent an unauthorized scanning of the vehicle security ID number, the code ________ with each use of the system.


A) changes
B) is reversed
C) is erased
D) is incremented by 1

E) A) and C)
F) B) and C)

Correct Answer

verifed

verified

Tamper mode is when what occurs?


A) The engine will start and run as normal except that the security warning light on the dash will be on all the time.
B) The security lamp flashes about once per second if the system detects a bad key, lock cylinder, or security-related wiring problem. The engine will not start or if it does start, will not continue to run.
C) The security dash lamp comes on for 2 to 5 seconds for a bulb check when the ignition is turned on, then goes out.
D) Any of the above, depending on the make, model, and year of the vehicle.

E) B) and C)
F) All of the above

Correct Answer

verifed

verified

A shock sensor is part of the vehicle ________ system.


A) speed sensor
B) fuel injection
C) content theft protection
D) immobilizer

E) A) and C)
F) A) and D)

Correct Answer

verifed

verified

Immobilizer diagnostic trouble codes are often found under what area?


A) Engine-related "P" codes
B) Body-related "B" codes
C) Chassis related "C" codes
D) Either B or C

E) A) and C)
F) A) and B)

Correct Answer

verifed

verified

Showing 1 - 20 of 23

Related Exams

Show Answer